When a Fire Door Stops Closing and Latching on Its Own
A fire-rated door only does its job if it closes by itself and latches every time. In a busy building, that is easy to lose track of. A closer gets weak, a hinge sags, someone props the door with a wedge, a latch stops catching the strike, and the door that is supposed to hold back smoke and fire now just swings in the stairwell or corridor.
Liberty Door Repair LLC handles fire door repair for offices, retail buildings, medical practices, schools, restaurants, warehouses, and multi-tenant properties in Roswell. We are a locally owned company based in Cumming, a short trip up GA-400, and our team has served North Georgia businesses since 2015, hinges, latches, and exit hardware that make a rated opening work.
If you are looking for fire door repair in Roswell, GA, we look at the whole opening, not just the part that is obviously broken: the door leaf, the frame, the hinges, the closer, the latching hardware, the strike, and anything that might be holding the door open when it should not be.
Fire Door Work We Handle
A typical fire door visit can include:
- Door closer adjustment, repair, or replacement, so the door closes fully from the open position without slamming.
- Hinge repair and replacement when a door sags, drags on the floor, or rubs the frame.
- Latch and strike alignment, so the latch bolt engages every time the door closes.
- Panic and exit device repair on rated stairwell, corridor, and exterior doors.
- Hollow metal door and frame repair, including bent edges, damaged frames, and doors that no longer sit square.
- Removing improper hold-open fixes, such as kick-down stops or wedges on doors that are meant to stay closed.
- Fire door replacement and installation when a door or frame is too damaged to repair.
For more on rated doors, see our fire door repair and installation page.
What Roswell Facility Managers Call About
Whether the building is a shop or restaurant near Historic Roswell and Canton Street, an office along the GA-400 corridor, or a multi-tenant property elsewhere in town, the calls about fire doors tend to sound alike:
- The stairwell door stops a few inches short of closed and just hangs there.
- The door closes but bounces off the frame without latching.
- A corridor door slams hard enough to rattle the frame or worry staff.
- The door drags on the floor or has to be lifted to latch.
- The panic bar on a rated door sticks, or the latch does not retract cleanly.
- An inspector or fire marshal flagged a door that does not self-close or latch.
Each of those symptoms has a likely cause. A door that stops short is often a closer that needs adjusting or has lost fluid. A door that bounces back usually has a latch and strike that no longer line up, often because a hinge has worn or the frame has shifted. We trace the problem back to the part instead of replacing hardware until the door happens to behave.
We are open daily from 7:00 AM to 7:00 PM, and same-day service is our goal when the schedule and the job allow. If a fire door in your building is not closing or latching, call 404-244-7253 as early in the day as you can.
How a Fire Door Service Visit Typically Goes
It starts with a phone call. We ask where the door is, what it is doing, whether it has a panic bar or a lever, and whether an inspection report mentioned it.
On site, the technician opens the door fully and lets it close on its own several times, from different positions. We watch the closing speed, the latch, and how the door meets the frame. Then we check the hinges and screws, the closer arm and body, the latch and strike, and the condition of the door edge and frame.
We explain what we found in plain terms and what it takes to fix it. Many problems come down to an adjustment, a new closer, or a set of hinges that we can handle on the spot. If a part or a replacement door has to be ordered, we tell you that and talk through how the opening can be handled in the meantime.
Before we leave, we test the door from both sides: it should close from fully open, latch without help, and open freely from the egress side with the exit hardware.
Why Use a Commercial Door Company for Fire Doors
A fire door is a system. The door, frame, hinges, closer, and latching hardware all have to work together, and a problem in one shows up as a failure in another. Because commercial doors are all we do, we can repair the closer, rehang the door, align the strike, and service the exit device in the same visit. When a closer is the main problem, our door closer services page explains that work in more detail.
From our locations we serve Roswell, north Fulton, and Forsyth County, and we travel to commercial properties within about 75 miles of downtown Atlanta.
Frequently Asked Questions
Why won’t our fire door latch when it closes?
The most common causes are a closer that is set too weak or has failed, hinges that have worn and let the door sag, or a latch and strike that have drifted out of line. We check each of those before recommending a fix.
Can we prop a fire door open during busy hours?
Fire-rated doors are meant to close and latch on their own, so wedges and kick-down stops work against them. If a door needs to stay open during the day, talk with your fire marshal or code official about approved options. We can remove improper hold-opens and repair any damage they caused to the closer or hinges.
When can you come out to Roswell?
We are open seven days a week from 7:00 AM to 7:00 PM and aim for same-day service when the schedule and the repair allow. Call 404-244-7253 as early as you can.
Schedule Fire Door Repair in Roswell
For fire door repair, closer and hinge work, or exit hardware service in Roswell, call Liberty Door Repair at 404-244-7253 or send a request through our contact page. For other entrance work in town, visit our door repair in Roswell page. We are open daily from 7:00 AM to 7:00 PM, with same-day service when the schedule and the job allow.